Resources
OSHA 10 vs OSHA 30: Which Outreach Course Fits
The OSHA 10-hour course is hazard awareness for workers; the 30-hour course goes deeper for supervisors and anyone with safety duties. Both come from OSHA’s voluntary Outreach Training Program, in construction and general industry versions. Here is which one fits whom, what the card shows and what California asks for, as of November 2026.
OSHA 10 vs OSHA 30 in brief
Pick the 10-hour course for workers who need to recognize and avoid common job hazards. Pick the 30-hour course for supervisors, leads and anyone who carries some safety responsibility, because it covers more topics in more depth. Then pick the industry: Construction for job sites, General Industry for most other workplaces.
Both belong to OSHA’s Outreach Training Program, taught by OSHA-authorized trainers. A student who finishes gets a 10-hour or 30-hour course completion card. Under federal law the program is voluntary, and OSHA says it does not meet the training any OSHA standard requires. The card is not a certification or a license, and OSHA does not let trainers advertise it with either word.
Which course is meant for whom
OSHA runs the program for construction, general industry, maritime and disaster site work. The table sets out each course as OSHA’s 2024 procedures describe it.
| Course | Meant for | What it covers, as OSHA describes it |
|---|---|---|
| Construction 10-hour | Construction workers | A one-hour Introduction to OSHA, four hours on the Focus Four hazards (falls, electrocution, struck-by and caught-in or between) with at least 90 minutes on falls, plus personal protective equipment and health hazards in construction. Electives include excavations, scaffolds, stairways and ladders, cranes, confined spaces and hand and power tools. |
| Construction 30-hour | Supervisors and workers with some safety responsibility on construction sites | The 10-hour topics in more depth, six hours on the Focus Four, and managing safety and health: safety programs, site inspections, accident investigation and safety meetings. |
| General Industry 10-hour | Workers at general industry work sites | Introduction to OSHA; walking and working surfaces including fall protection; exit routes, emergency action and fire prevention plans; electrical; personal protective equipment; hazard communication. Electives include lockout/tagout, machine guarding, bloodborne pathogens, ergonomics, powered industrial vehicles and materials handling. |
| General Industry 30-hour | Supervisors and workers with safety duties outside construction | More general industry topics, covered in more depth. |
| Maritime 10 and 30-hour | Maritime workers and supervisors | Maritime hazards; cards issued since April 1, 2019 do not expire. |
| Disaster Site Worker | Workers heading into disaster-site conditions | A 7.5 or 15-hour course including air-purifying respirator use; it does not meet HAZWOPER requirements. |
OSHA’s construction procedures give the reason for the time on falls: they are the leading cause of construction deaths. In every version, the stress is on spotting, avoiding, controlling and preventing hazards rather than reading standards line by line, and the Introduction to OSHA module shows students a sample Form 300 injury log, the record explained in our OSHA 300 log guide.
The industries do not mix. A trainer cannot count one combined class as both a Construction and a General Industry 10-hour. A 10-hour student can move up to the 30-hour with 20 more hours, if the same trainer teaches both parts, everything is done within 180 calendar days and the original 10-hour card is handed back.
How classes run, in person and online
OSHA’s Outreach requirements, effective October 1, 2024, set the same ground rules for every class:
- The student attends the whole class and finishes every required topic and the minimum hours.
- No more than 7.5 contact hours a day, so a 10-hour class takes at least two days and a 30-hour class at least four. Breaks, meals, roll call and optional tests do not count.
- The class can stretch over days, weeks or months but has to finish within 180 calendar days.
- Video fills no more than a quarter of the teaching time, and the class includes hands-on or interactive work.
- Trainers make every reasonable effort to confirm each student’s identity, and in-person classes top out at 40 students, with stated exceptions.
Self-paced online classes come only from OSHA-authorized online providers, which are independent of OSHA and listed on its site; individual trainers cannot offer them. Live video classes are allowed with cameras and audio on throughout, no more than 20 students unless a proctor is present, and no phones used to teach or take the class. OSHA names the in-person classroom as its preferred method. OSHA sets no age floor, students do not have to be employed, and a class can run in another language or with a qualified interpreter, which adds time.
What the student card shows, and how to check one
The card shows the person finished an Outreach class. It is neither a license nor a certification.
- The trainer gets the card to the student within 90 calendar days of the class ending, and it goes straight to the student whoever paid.
- Trainers cannot alter cards or add details such as a company name.
- Current plastic cards carry a QR code on the back that leads to the OTI Education Center that processed the card.
- Construction, General Industry and Disaster Site cards have no expiration date under the federal program.
OSHA does not verify individual cards and keeps no national card database or class records. Trainers and online providers keep student records for five years, so to check a paper card you contact the trainer, and OSHA’s Outreach FAQ takes reports of suspected card fraud by email. A lost or damaged card is replaced by the trainer or provider who taught the class, once per class and only within five years of the class ending; after that the student retakes the course.
The trainer courses: 500, 501, 510 and 511
The numbered OSHA courses are for people who want to teach Outreach classes or work closely with the standards. They run through OTI Education Centers, a national network of nonprofit organizations OSHA authorizes to train. The centers are not funded by OSHA and charge tuition.
| Course | What it is | Prerequisite |
|---|---|---|
| OSHA #510 | Occupational safety and health standards for construction: finding and applying OSHA’s construction rules | None |
| OSHA #511 | The general industry counterpart of #510 | None |
| OSHA #500 | Trainer course for teaching Construction 10 and 30-hour classes | #510 finished no more than seven years earlier, plus five years of construction safety experience |
| OSHA #501 | Trainer course for teaching General Industry 10 and 30-hour classes | #511, plus five years of general industry safety experience |
| OSHA #502 and #503 | Update courses for construction and general industry Outreach trainers | Taken every four years to stay authorized |
A safety degree, a CSP or a CIH can stand in for two of those five years, but simply working safely in a trade does not count, and OSHA does not waive the course prerequisite. The Construction 30-hour is no substitute for #510. Since October 1, 2024 there is no grace period: a trainer whose authorization lapses cannot teach or issue cards until it is renewed. Trainers show their current trainer card at the start of each class and whenever asked.
Is an OSHA 10 card required?
Federally, no. The federal government requires no one to take an Outreach class. Some states and local governments have passed laws that do, and some employers and unions ask for a card before anyone steps onto a job site. Because the program is voluntary, whoever sets the requirement decides which card meets it.
Two state examples:
- New York requires workers on larger public work contracts to finish OSHA 10 before starting, with proof attached to certified payroll (Labor Law section 220-h).
- Nevada requires construction workers to hold an OSHA-10 card and supervisory employees an OSHA-30 card, shown within 15 days after hire (NRS 618.950 to 618.990).
California has no confirmed statewide OSHA-10 rule for construction or public works. Employers, general contractors, unions and project owners can still set their own, so read the bid documents and the subcontract. The one statewide mandate is narrow: since January 1, 2023, Labor Code sections 9250 to 9254 require workers who set up, run or tear down live events at public event venues, such as state and county fairgrounds, state parks and CSU and UC facilities that host events, to complete a 10-hour course. Leads and department heads need the matching 30-hour course plus an industry certification (Cal/OSHA live events FAQ).
Under that law the course can be the Cal/OSHA-10, an OSHA-10 with general entertainment safety, or the OSHA-10 that fits the job. Cal/OSHA does not teach the courses itself; its versions run through OTI Education Centers. The Cal/OSHA and federal courses differ, and Cal/OSHA advises taking its version where a workplace calls for it.
How Outreach differs from the training Cal/OSHA requires
An Outreach card and Cal/OSHA’s training duties are different things. The card is voluntary and general; the Cal/OSHA duties are mandatory and belong to the employer, who shapes them around its own hazards. A 10 or 30-hour card does not satisfy any of them.
| Cal/OSHA duty | Who it covers | What it asks |
|---|---|---|
| Injury and Illness Prevention Program (section 3203) | Every California employer | Training when the program starts, at hire, on a new assignment, when new substances, processes or equipment bring a new hazard, and when a new hazard comes to light; supervisors learn the hazards their crews face. Records are kept at least one year. |
| Code of Safe Practices and toolbox meetings (section 1509) | Construction employers | A written code posted at the job-site office or given to supervisors, and toolbox or tailgate meetings at least every 10 working days. |
| New-hire safety instruction (section 1510) | New construction employees | Instruction on the hazards and safety measures of the work, and direction to study the Code of Safe Practices. |
| Outdoor heat illness (section 3395) | Outdoor work that can reasonably expose people to heat illness | Instruction for workers and their leads before the work, on risk factors, water, shade, cool-down rest, signs and symptoms, acclimatization and emergency response. |
| Indoor heat illness (section 3396) | Indoor workplaces reaching 82 degrees Fahrenheit with employees present, since July 23, 2024 | Instruction for workers and their leads under the indoor rule. |
Our Cal/OSHA IIPP template walks through the written program and its instruction records. For the training OSHA standards do require, OSHA points to its Publication 2254, Training Requirements in OSHA Standards.
Get help
A contract that calls for OSHA 10 cards usually comes with insurance terms too: certificates, additional insured wording and workers’ comp proof. Mithril1 is an insurance agency, not a training provider, so the course choice stays with you and the contract. What an agent can do is read the insurance side of the same bid with you. See our insurance for contractors, the contractor insurance checklist and requirements by trade, or send us the bid’s insurance section.
A few useful answers
Common questions
What is the difference between OSHA 10 and OSHA 30?
The 10-hour class teaches workers to recognize and avoid common hazards. The 30-hour class is built for supervisors and workers with safety responsibility and covers more topics in more depth. Both come in Construction and General Industry versions.
Does California require OSHA 10 for construction workers?
No. As of November 2026, California has no statewide OSHA 10 rule for construction or public works. Employers, general contractors, unions and project owners can set their own requirement, so the bid documents and subcontract decide.
Is an OSHA 10 card a certification?
No. It is a course completion card. OSHA bars trainers from advertising Outreach classes with any form of the words certify or license, and the card does not meet the training an OSHA standard requires.
Do OSHA 10 and 30 cards expire?
Construction, General Industry and Disaster Site cards carry no federal expiration date. Maritime cards issued since April 1, 2019 do not expire either.
How do I verify an OSHA 10 card?
Contact the trainer or online provider who taught the class, since OSHA keeps no national card database. Current plastic cards also have a QR code on the back that leads to the OTI Education Center that processed them.
Does an OSHA 30 card cover Cal/OSHA’s training rules?
No. IIPP instruction, construction toolbox meetings and heat illness training are separate duties the employer runs for its own hazards. A 10 or 30-hour card satisfies none of them.
